Grade Q345 Imported Tube does not conform to grade S355

Import Replacement Program

Value Added Exports



011 823 2377
086 777 7723
[email protected]

Physical Address:
15 Brook Road, Lilianton, Boksburg

Postal Address:
PO Box 18587,
Sunward Park,
Colin Shaw - Executive Director
Margaret Olivier - Secretary

Site by :




29 June 2010

Grade S355 Tube launched in February 2010 in the major centers in South Africa by ASTPM and SAISC
Grade S355 Tube, or often know as Structural Hollow Sections, was launched in February in Cape Town, Durban and Johannesburg. This project was a joint venture between the Association of Steel Tube and Pipe Manufacturers (ASTPM) of South Africa and the Southern African Institute of Steel Construction (SAISC). Over 450 Architects, Engineers, Fabricators, Merchants and Manufacturers of steel and steel products attended the launch. Colin Shaw, the Executor Director of the ASTPM, introduced the background to the launch. Franco Mordini, chairman of the technical committee of the Association of Steel Tube and Pipe Manufacturers, introduced the S355 size range and presented the benefits of this move forward in the market development of tube in South Africa. Guest speaker was world renowned tubular expert Professor Jeffrey A Packer. Professor Packer presented the many benefits and advantages of Tubes and encompassed technical aspects such as fabrication and design to the architectural aspects.  Spencer Erling introduced the various speakers.
ArcelorMittal, Macsteel Tube and Pipe, Robor and Trident Sterling actively promoted the launch in the various centers. The improved technology that users’ laser and plasma to cut tube was also promoted as an opportunity to make Tubular fabrication simpler and more attractive. Highveld also took the opportunity to promote S355.
An important part of the day for the Design Engineers was devoted to the Tubular Design course also presented by Professor Jeffrey A. Packer. 160 candidates countrywide attended the design course. The highly successful course included very important Golden rules when designing in Tube.  Part of the course was devoted to the currently under-utilized method of concrete filled columns. Benefits of this form of construction include increased load capacity of the member and very importantly the increased fire rating of the composite member.
Spencer Erling presented important welding and fabrication consideration when using tubular members. 
The launch of Grade 355 tube introduces another chapter in the Development of Tubular construction in South Africa. The ASTPM looks forward to the opportunities the new grade will present. The tips shared by Professor Packer at the course will assist Design Engineers to optimize designs that will result in both more efficient structures but importantly simplify the fabrication thereof.
For more information contact Colin Shaw on (011) 823-2337 or on e-mail [email protected]   For technical information Franco Mordini can be contacted at (011) 897-2137 or on e-mail [email protected].



LATEST NEWS      September 2012.

Graded Structural Steel Hollow Sections

It has come to the attention of the Association of Steel Tube and Pipe Manufacturers (ASTPM) that un-graded, commercial quality steel is being supplied into the Structural Hollow Sections in sizes range as defined by SANS 657 Part 1 and also reflected in the SAISC’S Red Handbook. These sizes may be manufactured locally or imported.
The ASTPM therefore strongly recommends that when graded steel is specified by the Engineer for use in Structural Steel Hollow Sections, that the Engineers and fabricators verify that the grade supplied meets the minimum requirements laid down in the design. This can be done by locating the 355 and manufacturer’s logos hard stamped on the tubes at roughly one meter centres and/or requesting test certificates. The hard stamping only applies to “small bore” sizes, as large bore sizes are marked differently on the tubes and labels. The large bore sizes are indelible marked with the steel grade and manufacturer’s logo. Small bore are sizes include Circular Hollow Sections smaller than or equal to 219.1x6, Square Hollow Sections smaller than or equal to 150x150x6 and Rectangular Hollow Sections smaller than or equal to 200x100x6. Larger sizes and thicknesses are defined as large bore.
The standard grade in the Structural range for the industry is S355 and X42 or X52/S355 for the small and large bore sizes respectively.
Should you have any doubts or would like to know more you can contact the ASTPM (Tel. 011-823-2377) for assistance. 
Franco Mordini, Chairman of the Technical Committee of the ASTPM and Business Development Specialist for Macsteel Tube and Pipe.
7 September 2012

Back to Top

Africa Pipe Industries | ArcelorMittal S.A. | Aveng Trident Steel | Barnes Tubing | Bosal Afrika | Group 5 Pipe | Hall Longmore | Home | Import Replacement Program | Macsteel Tube & Pipe | Neven Matthews | New Concept Mining Pty Ltd | News | Proroof Manufacturing | Response | S355 Structural Tubing | Value Added Exports |